Stylin Online T-Shirts
Register Rules Be A Supporter Members List Social Groups Mark Forums Read
Hobby Link Japan TFSource Big Bad Toy Store Robot Kingdom ToyArena Captured Prey

Universe 2.0 Dinobot - Raptor Robot Kibble Fix

Closed Thread Thread Tools
Old 11-18-2012, 05:33 AM   #1
Matt Booker's Avatar
Join Date: Sep 2008
Posts: 1,355
Location: Illinois
Universe 2.0 Dinobot - Raptor Robot Kibble Fix

Universe Dinobot isnít a bad Transformer, even if the color scheme is a bit questionable. Itís got a decent robot mode, but while the dinosaur mode is better than the original, it doesnít even try to hide the robot arms.

Take a look at this picture in the TFW2005 Resources section:

The raptor thighs donít cover the robot thighs, but Iím okay with that. They may not look great from the front, but at least they look good from the side. But the robot hands, they stick out under the dinosaur face and donít look good from any angle.

The mod for how to fix this is easy, and doesnít require cutting the figure or even gluing it.

Step 1 Ė Swap The Arms

Yep. Just swap the arms. The shoulders are on balljoints so they pop off and on with no problems.

The arms are backward at this point, so youíll have to turn them around at the upper arm swivel.

Before you complain about the fingers and thumbs being reversed, read on to the next step!

Step 2 Ė Swap The Fingers And Thumbs

The fingers and thumbs are on pin joints, so you might think that swapping them wonít be as easy as the arms were. Normally, that would be right. Pin removal can be difficult, after all.

But this step doesnít require pin removal! Dinobotís fingers and thumbs are made from rubbery plastic, and they can be removed by easily bending one side off the pin and then sliding the other side off as well. It doesnít damage the plastic, and you can use the same method to put them back on after swapping them.

Step 3 Ė Filler!

Now that the fingers and thumbs are swapped, Dinobotís hands look good but the arms have hollow spots. Those spots could be filled by anything you want, whether spare plastic to look like techno bits or if you want to sculpt and paint matching dino bits. What I used was a spare twist tie. Dinobot has bone spikes as a theme in his robot mode, and the look of a coiled twist tie matches that. Get a longer twist tie and wrap a section around a pen. Once youíve wrapped it around twice, cut off that section and make another.

Two coils are all you need for each arm, each with the tips pointing the same way. They should be just big enough to fit tightly in the hollow upper arms. This will take some massaging, but keep adjusting it until it looks good.

The robot fist is still showing, and there are two hollow sections where the show accurate thumbs would fit before the mod, but those donít bother me much. A couple of twist tie pieces could be glued in the hollow sections, and the robot fist could be covered up with some plastic scraps or even sculpted over.

But with the mods so far, the robot mode already looks great.

But the bot mode already looked good. So whereís this improved dinosaur mode?

To get to that, you have to alter the transformation. Swapping the arms was the important part for this, with the other stuff just being cosmetic changes to the robot mode. Before, the arms would fold up onto the chest. The upper arms still form the chest, but now the lower arms fold down between the legs. Just turn the arms so that what is now the outer edges are facing each other. The dinosaur skin should be facing the outside, and the lower arms form the gut.

Fold the robot mode fingers together and theyíll sit snugly up against the trigger/storage hook on the tail.

Take a look at this picture:

Compare that with this.

The arms are easy to swap, so try it out and see if you like it. Dinobot has a bit of a bigger gut in dinosaur mode, but the difference in hand is significantly better. The robot fingers are still just folded up, but theyíre hidden between Dinobotís dinosaur legs. It does, however, look like HP Lovecraftís interpretation of goatse.

~Matt Booker

Originally Posted by closetrat View Post
Sweet mother of pearl - now I gotta find this mold!

Don't worry about the gut bulk - looks fine as far as I can tell...

No problem. Seeing the gut area on an unmodded version looks really empty now. This looks a lot more natural, especially considering your link.

But it's something best seen in hand. Since all that really needs done to try it out is swapping the arms, it's easy to try out if you've got a Dinobot.
Attached Thumbnails
-dinobothand.png   -dinobotarm.png   -dinobotbot.png   -dinobotdinogut.png   -dinobotdino.png  

-dinobotdinobutt.png   -dinobot036.jpg  

Last edited by Superquad7; 11-21-2012 at 02:09 AM..
Matt Booker is offline  
Closed Thread

Thread Tools

Posting Rules
Forum Jump

Hobby Link Japan