Stylin Online T-Shirts
 
Register Rules Be A Supporter Members List Social Groups Mark Forums Read
Hobby Link Japan TFSource Big Bad Toy Store Robot Kingdom ToyArena Captured Prey

Bodywork 101: Part One

Closed Thread Thread Tools
Old 03-13-2011, 10:41 PM   #1
Semi-retired customizer
Wikkid's Avatar
Join Date: Oct 2004
Posts: 1,488
Location: Saskatchewan, Canada
Collection Count: 120
Bodywork 101: Part One

Part 1: Creating Contors:

Begin by gluing styrene or whatever substrate you plan on using to the project. Shown here is styrene panel bonded to Masterpiece Starscream’s hip junk. This will become a rear quarter panel for a MP Hot Rod project:




The factory part already had a flow that suited this project but needed to be widened and curved in specific areas. I begin by putting down a piece of 80 grit sticky back sandpaper to my desk top. I then sand the area down in a rocking motion to achieve a gradual curve. It's important to use long strokes and be sure not to press hard. Let the grit do the cutting:




I use the same technique on the other side of the panel:




Now, to cover the whole thing in filler:




Follow the same technique as before and round your panel out to your liking. Do not sand it all off; we're trying to create a larger, rounded body panel:




[The] side panel gets the same treatment. On this side, I rounded the lower quarter to curve inwards towards the rocker panels:




Wrapping a piece of sandpaper around my finger, I . . . .




. . . . notch out a combination crown in the forward section of the quarter panel. This then needs to be worked into the other high crowns by sanding the curves lightly:



The panel takes shape as so. I'll need to go in a put a quick skiff on the dark red area which is a low area then sand it out:




Always be sure to test fit your parts:





Part 2: Filling and Tightening Gaps Around Moving Parts:

I begin by filling the 90 degree angle in the fender wedge. This is done to eliminate the joint line and create a seamless flow between the two panels:




After sanding the whole area for the sake of adhesion, I fill over everything end to end:




After sanding out the fender in the same way I did the quarters earlier, I fold a piece of sandpaper and finish the inner fender to hood edge:




The finished product here is the hood flowing directly into the fender and the fender into the bumper. I also re-arched the wheel well:




Using a razor knife, I score the edge where the panel is to detach. Do not cut too deep or you'll end up with wide gaps again:




The panel should just pop off clean if the prep work was done right and the product is sound:




Part 3: Fixing Mistakes:


On this project, I went and installed a matrix bay within the hood/chest. This was all done without the actual matrix in place, so once I cut the opening and installed the hinges and matrix, it pushed the panels outward. I'm way too lazy to start over on this after all the work, so I cheated by raising the rest of the panels to align:




After prep-sanding everything, once again we apply filler to the entire area:




Using the earlier techniques of long strokes and a gradual curve, the panel is sanded to fit again:




Now we score the outer edge once again:




There's the church and there's the steeple. Open the doors and see all the people:




Then close it up to see how well everything fits. If the alignment problem remains, fill again until everything sits true:

Attached Thumbnails
Bodywork 101: Part One-waggy.jpg   Bodywork 101: Part One-scratch1e.jpg   Bodywork 101: Part One-scratch2.jpg   Bodywork 101: Part One-scratch3.jpg   Bodywork 101: Part One-scratch4.jpg  

Bodywork 101: Part One-scratch5.jpg   Bodywork 101: Part One-scratch6.jpg   Bodywork 101: Part One-scratch7.jpg   Bodywork 101: Part One-scratch8.jpg   Bodywork 101: Part One-scratch9-1-.jpg  

Bodywork 101: Part One-scratch9.jpg   Bodywork 101: Part One-scratch10.jpg   Bodywork 101: Part One-scratch11.jpg   Bodywork 101: Part One-scratch12.jpg   Bodywork 101: Part One-scratch13.jpg  

Bodywork 101: Part One-scratch14.jpg   Bodywork 101: Part One-scratch16.jpg   Bodywork 101: Part One-scratch17.jpg   Bodywork 101: Part One-scratch18.jpg   Bodywork 101: Part One-scratch19.jpg  

Bodywork 101: Part One-scratch20.jpg   Bodywork 101: Part One-scratch21.jpg   Bodywork 101: Part One-scratchs.jpg  

Last edited by Superquad7; 10-15-2013 at 01:58 AM..
Wikkid is offline  
Closed Thread


Thread Tools

Posting Rules

TFSource.com