|02-20-2008, 11:34 AM||#1|
'Till All are One!
Join Date: Jan 2004
Location: BC, Canada
Collection Count: Used to be 100's--now 70 (and counting!)
I tried to post this is the tutorial section but couldn't; I assume only mods have that power.
As the name suggests, we’re going to make a basic flame pattern. There are many different ways to do it; I’m going to show you a simple method involving a mask that can be used with an airbrush or aerosol cans. You’ll need:
* role of low-tack painters tape (green or blue); the wider the better.
* sharp blade
* pencil and white eraser
* sketch of how you want your flames to look
First, a comment about paints. Drying times and curing times are not the same thing. Paint may dry in one hour, but can take up to ten days to cure (properly harden and become fully ‘stuck’ to the substrate it’s been applied to). You need to know the dry and cure time for your paints before you attempt this. As a general rule:
Lacquers take 4-5 days to cure
Krylon takes 7 days to cure (it’s similar to a lacquer)
Oil enamels take up to 10 days to cure (quick dry enamels may cure a little faster)
I have no idea the dry or cure time on acrylics as I don’t use them. If someone knowledgeable about them wants to pm me that info, I’ll add it. After all, it’s not the tools—it’s the workmanship.
Why does this matter? Because we’re going to be taping off and burnishing a completely painted surface to make our flames, and we don’t want the paint to lift. As a former professional painter, I can tell you there’s nothing worse than having to do the job over again because you rushed your tape job. As a rule of thumb, I like to wait half the full cure time before taping. Also, you need to make sure the paint you’ll be using for your flames is compatible with the base-coat you’ve applied. Never apply acrylics on top of oils or lacquers; they simply don’t bond well. In the following project, I’ve used oil enamel for the base coat, and synthetic lacquer for the flames.
Here’s my painted wing, with some of the markings already applied.
Using the painters tape, lightly tape of the entire surface. You need to pull this off, so don’t press hard or burnish it. I should have used wider tape, but none of the paint stores in my area had any. That’s ok, just overlap the tape half a centimeter or so. The overlaps must be lightly burnished to prevent bleed. Burnishing in this context just means rubbing the surfaces so they have a tight bond; your thumb and thumbnail work just fine.
You should already have a sketch made with the flame pattern you want.
Copy the pattern onto the tape with a pencil (I’ve used pen because it photographs better, but traced my pencil marks). You can erase any mistakes with a good white eraser, so don’t be afraid to do so. Just make sure you don't lift any of your tape overlaps.
Pull the tape off, and place it on a cutting board. Note that if you’ve used multiple layers of tape as I have, you must cut “down” the tape, so you don’t lift your overlaps.
Carefully cut out your mask. This is the most important step in getting nice flames, so don’t rush it!!
Position your mask on your piece, and burnish the edges well.
Then paint, using multiple light coats…I used 3 or 4 to get the colour I wanted. As soon as you’re satisfied with your paint job, pull your mask off. I wait a few hours, then ¬gently go over the flames with 5000+ grit sandpaper to minimize the paint lines at the mask edge.
That’s it! You may need to do slight touch-up on your base coat.
You could so this several times, to create multi-colour flames, or flames with shadows (using this method means the shadow layer is the first one to paint) but you’ll have to make sure you don’t paint too heavy, or you’ll get raised paint lines, and you’ll need to use high-grit sand paper between each coat (if you do that, try to avoid metallics—they don’t sand so well).
Hope this is useful!
|Latest News & Rumors Posts|
|TFW2005 May 2016 Poll - How do you feel about the Titans Return line so far?|
|Titans Return Hot Rod Revealed|
|Titans Return Leaked Images of Potentially Upcoming Figures|
|Masterpiece MP-30 Ratchet in April.|
|Cyber Battalion Optimus and Starscream being released as Universal exclusives|
|Latest Toy Discussion Posts|
|The Masterpiece Appreciation thread|
|The Amazon New/Restocked/Shippe...|
|MP Shockwave Discussion Thread|
|Combiner Wars Appreciation Thread|
|Let's see some cool stuff *2016* TF Edition **Rules In First Post**|
|Latest 3rd Party Posts|
|Upscaled KO Masterpiece Grimlock|
|The Knock off transformers thread|
|MMC / Ocular Max Backdraft (Inferno)|
|Let's See Some Cool Stuff 2016 Third Party Edition **Rules in First Post**|
|Maketoys Guardia (Defensor)|
|Latest Radicons Posts|
|The Hot Rod Trio!|
|Unnamed evil "Titan" as a steel-mill (W.I.P.)|
|MP-10/MP-22 Matrix Of Leadership-3D Printed|
|Custom MP-10 Optimus Prime, DotM Leader, MP-27 Ironhide (Pic Heavy)|
|Classics Black Zarak|