Ratchet EMP Generator

Discussion in 'Transformers Toy Discussion' started by jestermon, Jun 8, 2008.

  1. jestermon

    jestermon Well-Known Member

    Joined:
    May 10, 2006
    Posts:
    7,600
    Trophy Points:
    232
    Likes:
    +8
    I do not know if any one has mentioned it but if you have Lockdown and Ratchet, lockdowns Engine block/Ratchet's EMP generator, it losk into the spot on ratchets wrist, very neat cross figure feature.
     
  2. NGW

    NGW Rawr

    Joined:
    Sep 4, 2006
    Posts:
    7,669
    News Credits:
    2
    Trophy Points:
    232
    Likes:
    +13
    This has been noted a few times before.

    Is rather neat though, yes.
     
  3. Kingplay

    Kingplay Banned

    Joined:
    May 15, 2008
    Posts:
    1,430
    News Credits:
    1
    Trophy Points:
    126
    Likes:
    +1
    Ebay:
    nice! didn't know that, got a picture?
     
  4. MegaHavok

    MegaHavok Well-Known Member

    Joined:
    Jul 12, 2002
    Posts:
    4,506
    News Credits:
    18
    Trophy Points:
    186
    Likes:
    +18
    Check the feedback forums for pics. Most of these little features are well covered in there. There is also a way to connect it to prowl
     
  5. SoundMaster

    SoundMaster Likes RID Bulkhead.

    Joined:
    Oct 14, 2007
    Posts:
    3,469
    News Credits:
    1
    Trophy Points:
    166
    Likes:
    +1
    This has been known, I learned this in Peaugh's review.

    Anyhoo, it's a really nice feature. When my bots are in robot, I alway's give it to Ratchet.
     
  6. Transquito

    Transquito Reach For The Light TFW2005 Supporter

    Joined:
    Dec 23, 2007
    Posts:
    2,549
    Trophy Points:
    181
    Likes:
    +2
    Old news, but they're still damn cool !

    My Ratchet and Lockdown is on there way from the US, and i cant wait to try this out !
    ... i just dont hope that the generator will be 2 lose to fit in ...
    Well, nothing a lil of clear nail polish cant fix? :p 
     
  7. jestermon

    jestermon Well-Known Member

    Joined:
    May 10, 2006
    Posts:
    7,600
    Trophy Points:
    232
    Likes:
    +8
    tight

    Actually every thing is nice and tight, when you are transforming them be careful the plastic they are using for these is different then usual and the joints and pegs seem to all be very sturdy.
     
  8. Deceptigtar

    Deceptigtar Sworn Decepticon Assassin

    Joined:
    May 24, 2006
    Posts:
    13,008
    News Credits:
    63
    Trophy Points:
    277
    Likes:
    +64
    Ebay:
    i had to shave the peg down on my ratchet to make it fit.
     
  9. T16skyhopp

    T16skyhopp Well-Known Member

    Joined:
    Mar 10, 2007
    Posts:
    5,049
    News Credits:
    4
    Trophy Points:
    191
    Likes:
    +4
    Ebay:
    same
     
  10. SPLIT LIP

    SPLIT LIP Dry built

    Joined:
    Oct 22, 2005
    Posts:
    66,411
    News Credits:
    2
    Trophy Points:
    407
    Location:
    agile house
    Likes:
    +919
    It's not really attached, I just sorta set it on the lightbar when I made that up. :p  One could modify the hole on the EMP to make it snug.

    I don't have this problem.
     
  11. Peaugh

    Peaugh Hi.

    Joined:
    Aug 7, 2006
    Posts:
    11,609
    News Credits:
    204
    Trophy Points:
    312
    Likes:
    +271
    Actually, someone found a way to snap the lightbar on Prowl into the groove on the side of the EMP.
     
  12. Autovolt 127

    Autovolt 127 Get In The Titan, Prime!

    Joined:
    Nov 26, 2006
    Posts:
    82,130
    News Credits:
    16
    Trophy Points:
    412
    Likes:
    +483
    Well it can also gon on Prowl,Split lip should use that.
     

Share This Page