Customs: In need of a few custom parts

Discussion in 'Requests' started by Forgotten_Prime, May 9, 2011.

  1. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    My list of needed parts.
    A small optimus prime head that can fit on a RiD prowl body an vehicle form.

    An open left hand for my classics cyclonus.

    Smaller launchers for my classics starscream


    Three heads that will fit the classics Scourge body each head has to look like shrapnel, bombshell, kickback in style
    A set of redesigned wings that can fit the Scourge frame the wings must be more flat an sleeked backed like classic Cyclonus

    Thank you.
     
  2. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    beep beep. any help? i was told this would be the place if i was unable to make the parts. so. any one.
     
  3. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    bump
     
  4. warriorpriest

    warriorpriest Priest of Primus

    Joined:
    Mar 5, 2008
    Posts:
    3,235
    News Credits:
    3
    Trophy Points:
    167
    Likes:
    +4
    For the Prime head try the classics 2pack. I think that one may work looking at the size.

    When you say open hand do you mean like wheeljack and tracks has?? or just a hole like his right hand?? If it is an open open hand just find a hand on any gen/rts toy that will work and steal it. Tracks/Wheeljacks, jazzs hand should all work with either partsforming or mods to the forearm. If you just want a hole in his hand you could use a dremel.

    For the smaller launcher...well unless you ant to risk ruining your launcher you could trim a little her and there but looking at my clear seeker it would be risky.

    the heads and wings would be harder route to go unless you find a good sculptor or someone that works well with plastic card.
     
  5. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    thank you for the tips. the head is to big by 2.5 mil. im haveing someone sculpt one for me.
     
  6. whiskeytango

    whiskeytango Combaticon

    Joined:
    Sep 12, 2008
    Posts:
    987
    Trophy Points:
    111
    Likes:
    +0
    I would recommend looking at peoples shapeways shops for different null rays. There are several good choices there.
     
  7. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    i just found that shapeways has some of what i need.
     
  8. Forgotten_Prime

    Forgotten_Prime Till All Are One

    Joined:
    Sep 15, 2010
    Posts:
    234
    Trophy Points:
    56
    Likes:
    +0
    hindge for wings. the idea is 5mil pin on one side of the hindge and an 5mil indent on the other. hopefuly it will look like a part of a wing.
     

    Attached Files:

  9. grimlockprime

    grimlockprime Well-Known Member

    Joined:
    Feb 5, 2008
    Posts:
    2,532
    Trophy Points:
    197
    Likes:
    +26
    contact me about the insecticon heads
     

Share This Page