g1 sixshot can he be made superposable? this one goes out to THEDEVASTATOR

Discussion in 'Transformers General Discussion' started by GENOZAUR, Dec 25, 2008.

  1. GENOZAUR

    GENOZAUR Banned

    Joined:
    Mar 17, 2007
    Posts:
    3,209
    Trophy Points:
    151
    Likes:
    +0
    this one goes out to THEDEVASTATOR

    would it be possible to modify G1sixshot and use a combination of lego exoforce clicking ratchet joints and lego tecknic 1x1 bricks with friction connector peg
    in such a way that it would give g1 sixshot complete posability through the shoulders, upper arms, elbows,lower arms and wrists?

    with the ratchet joints being used for the elbows and for the shoulder at the rotating joint which attaches the arms to the body?

    while the 1x1 lego technic blocks and friction connector peg joints would be used to build a set of rotating joints into the upper arms just above the ratchet jointed elbows and the lower arms just beneath the ratchet jointed elbows?

    for that matter would it also be possible to modify the body itself so that the lowerportion of the body from just beneath the chest would be able to rotate freely in full360 degree manner?

    would it also be possible to mod the wings so that they can slide backward and forward on his back into a slightly higher position thereby giving the lower body enough room to rotate?

    would it also be possible to mod the lower body in such a way that the cockpit control cabin itself serves as a double hinged folding joint so that when sixshot is transformed to his assault tank mode it would make it so that the entire lower body rotates around to the back with the lower body then folding up vie the double hinged cockpit control chamber with the lower body resting on top of the back of the upper body while the lower legs themselfes would fold up on top of the upper legs for the tank turrents portion of the tank vehicle mode?

    would it also be possible give sixshot a better set of thoroughly multi jointed clawed hands in such a way thatthey would at the wrist portion of each hand be set up on a floding hing assembly so that in either of his land based vehicle modes they could fold into place on the outer sides of the lower arms in such away that in tank mode they would serve as additional side armor to cover the treads from the side or in his armored carrier mode they would fold up onto the inner side of his lower arms and would serve as additional side armor to cover the front set of tires while in winged wolf mode they would also serve as the wolfs front set of clawed feet?

    would it also be possible to mod the upper legs and lower legs in such a way that just above and beneath the knee joint it would have a 2 sets of 1x1 technic bricks with friction connector peg so that the upper leg and lower legs would be able to rotate in a full360 degree manner?

    would it also be possible to mode the lower waist in such a way through the groin area that by using 2 sets of lego sliding flat panel parts the upper legss would be able to extend and retract into the waist?

    would it also be possible to mod the upper legs at the hips so that they would sport a set of modified lego exoforce clicking ratchet joints so that when the upper legs retract out from the lower waist the upper legs at the hip joint would have full posibility?

    would also be possible to mod the lower legs in such a way that when sixshot is transformed to winged wolf mode the upper legs would fold foward a few clicks at the hips while the lower legs at the kneejoint would fold up into place just behind the upper legs with the lower legs then folding down on top of the uppr legs at the kneejoint?


    would it alks be possible to mod sixshots guns in such a way that the could attach to the dual laser cannons that fold out of his lower legs in such away that both sets of guns when combined would serve as the lower set of legs for the winged wolfs hind legs?


    would it also be possible to replace the wolf head and robot head with a better head in which the back half of the robot head is itself formed from the wolf head with the wolf head and robot head being attached together by a hinged folding pin joint inwhich the wholf head fold up onto and over the optics and nose ofthe robot head with the robot head itself serving as the wolfs neck in wigned wolf mode?


    would it also be possible to articulate the new robot/wolf head at the neck by using a a set of modified 1x1 technic block and friction connector peg with it serving as a rotating joint in the neck so that the new robot/wolf head can rotate in a full 360degree manner?

    would it also be possible to modify the hollowed out chest in such a way that the new head could fold forward and down into the hollowed out head chamber with this rotating joint being built into a flat panel rotating joint that the bottom half of the technic rotating joint would be anchored into?


    would it be possible to make a quad set of geared tank treads out of technik parts in which they are made in as close to 1/1 scale as possible?

    would it also be possible to use the inmolded geared tank tread detailing on the outside of sixshots upper and lower arms both as a guide of sorts to work with in drilling 4 accurately placed holes into the outer side of the upper and lower arms and also as a way to effectivly mount the geared technik tank treads into place on the sides ofthe upper and lower arms after completely sanding off the inmolded geared tank tread detailing so as to provide a flat and smooth and level surface to work with in mounting the technic geared tank treads into place ?

    would it be possible to make the treads themselves using technic motorcycle chain parts?

    lastly of all would it also be possible to make enough room on the hollowed out insides of the upper and lower arms so that the crossaxle rods can be securely anchored into position on the inside using a series of cross axle extension parts to permanently mount them into place with and would it also be possible to make enough room for the technick tank treads so that they can move and rotate freely?


    it would take quite a bit of work , time and patience but i really do believe that it would be entirely possible to fully articualte g1 sixshot/greatshot/shadowmaru in such a way that the figure would be a reasonable melding of the original figure itself sixshots animation model and in some part even the idw take on sixshots character model

    what are your thoughts on the matter?
     
  2. GAUGE

    GAUGE In Art, Nothing Is Impossible.

    Joined:
    Jun 21, 2006
    Posts:
    10,061
    News Credits:
    4
    Trophy Points:
    267
    Location:
    Phx, AZ
    Likes:
    +37
    Isn't this something for the RADICONS section?
     
  3. Bottom Out

    Bottom Out Well-Known Member

    Joined:
    Jul 8, 2008
    Posts:
    1,199
    Trophy Points:
    126
    Likes:
    +0
    the answer would be yes...since pretty much anything is possible in the world of fabrication
     
  4. Sideways

    Sideways Banned

    Joined:
    May 17, 2006
    Posts:
    2,432
    Trophy Points:
    186
    Likes:
    +0
    maybe try PM'ing him with your question instead of making a thread.
     
  5. Ghost Prime

    Ghost Prime Banned

    Joined:
    Sep 1, 2004
    Posts:
    766
    Trophy Points:
    136
    Likes:
    +0
    its easy...all you need is a junker bot the same size and then use the ball joints onto that and mod the six shot to take the ball joint
     

Share This Page